منتديات جوردان سات فور يو الفضائية

منتديات جوردان سات فور يو الفضائية (http://www.jordansat4u.net/)
-   Dreambox 500 HD (http://www.jordansat4u.net/f327/)
-   -   DreamBox 500HD Tutorials (http://www.jordansat4u.net/t12221/)

fa7oom 03-24-2010 08:20 PM

DreamBox 500HD Tutorials
 
كود:

DM 500HD firmware update via browser

What you need to update the firmware:
You need a current image. Such an image for the DM 500HD has the extension *. NFI.
It is not possible einzuspielen another image type such as *. IMG!
Do not try it please, it does not work.
You still need a DHCP server on your network, an intact bootloader
You need a browser and a network cable. Connect your Dreambox to your
Switch / hub / router.
To import a new image to the Dreambox, you must have the "2nd stage" Loader
in place and undamaged.

The next steps refer to a network with a DHCP server running.
- Turn off the dreambox, use this switch back in the pits. The
Standby is not enough!
  • (1.) Press the button on the front panel and hold it down.

  • (2.) Turn on the Dreambox via the switch on the back of housing a

  • (3.) your Dreambox now get the next free DHCP IP address from your router.


http://img690.imageshack.us/img690/2162/66867779.jpg

- Now, open a browser on your PC.
(1.) Enter the IP address in the address field of the browser "http://ip/" field.
- (2.) Now press the pick "firmware upgrade" of the displayed page in
Browser.

http://img4.imageshack.us/img4/2011/69108872.jpg

- On the next page, you can now select the desired image you
dubbing in the box like. Please note the file extension *. nfi that
dub
other images is not possible (NO *. img)!
- Click on the selection of the images on the selection of "FLASH!" and wait
please
completely transferred to the image was flashed.
- Turn up the whole box, and then ask then on again.
The new operating software should now be recorded and boot


fa7oom 03-24-2010 08:20 PM

كود:

Manual update firmware DM 500HD via mini-usb

Upgrading the software of DM 500HD is like the rest of Dreams via RS232, but the mini-USB port.

Items required:
1) mini-usb male to male USB

http://img97.imageshack.us/img97/9338/16225260.jpg

2) Universal DreamUP 1.3.3.5 

Process:

1)Unplugged the Dream 500HD

2)We connect the cable for its part mini-usb port "Service" of the Dream 500HD and the USB to a USB port on your PC.

3)Just plug it in, the PC will detect new hardware connected to the system:

http://img696.imageshack.us/img696/8759/43881411.jpg

4)The PC will ask the driver for this new component. Download here New drivers Dreambox 500HD - DM 500HD Other Files

5)Open the ******s Device Manager, and you will see the new hardware installed, will appear as COM port (even a USB cable). In the following example, is recognized as the cable into the port COM4.

http://img709.imageshack.us/img709/4206/47870490.jpg

6)We opened the universal DreamUP 1.3.3.5 (for example) and select the update COM port (like any other model of Dreambox). At this point, we choose the COM port that we appeared in the previous step (COM4 in this example).

7)Press the Connect button the DreamUP universal and we can turn
the Dream 500HD to start loading new firmware.

http://img163.imageshack.us/img163/3828/18302634.jpg


fa7oom 03-24-2010 08:23 PM

Howto Enable USB on DM500hd

كود:

Here is the guide to activate Usb controller on your DM500hd with a little hardware modification.
Warning: Removing resistors means you are going to VOID WARRANTY and everything happening since then will be at YOUR OWN RISK, no one will take responsibility for your own actions.

Enabling USB port on DM500HD

On DM500HD there is a standard usb pinheader, but the usb controller has been fixed into a disable
state, because it misses an over-current protection on 5v pins (max1823 on dm800 for example) and
so it does not meet usb specs.
Removing a resistor (or two), you can fake the presence of such missing chip, but in case your usb
device makes a short, there will be no protection against flaming the main 5v mainboard regulator,
you can imagine what could happen. If usb specs requires an overcurrent protection, there must be a
good reason afterall.
Removing resistors means you are going to VOID WARRANTY and everything happening since
then will be at YOUR OWN RISK, no one will take responsibility for your own actions.

http://www.sat-universe.com/attachme...1&d=1268366301

You can see here the standard PC motherboard usb pinheader with a standard PC usb bracket
connected. The bottom-right pin is in real disconnected, you have to make an hole into the PC
bracket connector to let it feet. On the rear panel of the decoder, there is a pre-cut ****** for a
single usb female connector, if you want a stylish job.

http://www.sat-universe.com/attachme...1&d=1268366345

In my decoder there was only R1011 populated with a 0ohm resistor, but in case you have R1010
populated or both, you have to remove both. These are FAULTA and FAULTB signals that would
come from the missing max1823 usb power control switch, it’s enough to have one populated to
tell the Broadcom to disable the whole usb controller.

http://www.sat-universe.com/attachme...1&d=1268366382

Looking at usb specs, the device that must handle the over-current protection is the hub, so, instead
of directly connecting an usb device, I would suggest to buy a good usb external-powered hub
which reports “over-current protection” on the specs, because the cheap chinese ones does not have
a dedicated power control circuit. Googling a little, hubs with Genesys GL850 chip seem good
candidates.

http://www.sat-universe.com/attachme...1&d=1268366421


fa7oom 03-24-2010 08:24 PM

Install CCcam on original image

What follows is nothing dangerous or complicated to make, but will require basic knowledge of Linux:

1) We entered through telnet (or ssh) to the DM. The login / password by default is usually root / dreambox.

2 º) First of all, we must get rid of that comes standard cam (dccamd). We do this with the command:

كود:

ipkg purge dreambox-dccamd
3rd) transferred by FTP the binary CCcam to the directory: / usr / bin

4th) We execute permissions to binary:

كود:

chmod x / usr / bin / CCcam
5 º) Edited by FTP and then transfer the configuration file CCcam.cfg to the directory: / etc

6 º) Optional: we can transfer other files via FTP CCcam.providers CCcam.prio CCcam.channelinfo , etc directory: / etc

7th) Edit the file that runs automatically when you start the cam dreambox with the command:

كود:

vi / etc / init.d / bootup
8th) We and comment (we put # before) the line:


كود:

# / usr / bin / wdog / usr / bin / dccamd -
9th) Below that line add this one:


كود:

/ usr / bin / CCcam
10th) Reboot the DM:

كود:

reboot

samehfr 09-08-2011 11:33 PM

الف شكرا لك اخي الحبيب على هذا الموضوع القيم وعلى
هذا المجهود الرائع الذي يستحق كل تقدير


aziz2200 11-16-2011 09:39 PM

كل عام والجميع بألف خيرفى هذا المنتدى العظيم .

sharing 04-03-2012 09:52 PM

شكراااااااااااااااااااا


الساعة الآن 05:04 PM بتوقيت مكة

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2018, vBulletin Solutions, Inc.

JordanSat4U , Copyright ©2009-2012